Gravio Rental Devices Setup
Battery Powered Devices
Temperature Sensor
Monitor and measure temperature in real-time.
Learn how to set up
Door and Window Sensor
Detect if a door or window is open or close in real-time.
Learn how to set up
Motion Sensor
Detect movement at a distance.
Learn how to set up
Wireless Mini Switch
Control or trigger connected devices wirelessly.
Learn how to set up
Vibration Sensor
Detect movement and vibration of objects.
Learn how to set up
Self-Powered Devices
Temperature Sensor
Monitor and measure temperature in real-time.
Learn how to set up
Door and Window Sensor
Detect if a door or window is open or close in real-time.
Learn how to set up
Door and Windows Sensor

Product Introduction

The Aqara door/window opening and closing sensor examines the opening and closing state of a door or a window. If the the sensor unit comes close to the magnet, the repective state is sent to the Gravio Edge Server where appropriate Gravio Actions can be triggered in response.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-Door" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the Gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button in Gravio Studio.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Step 1: Remove the protective film.

Step 2: Align the marker line on the sensor unit and the magnet.

Step 3: Stick magnet and sensor device to doors or windows (It is recommended to install the sensor unit on the immovable surface, and the magnet on the moveable surface. Make sure the installation gap is less then 22mm when doorsor windows are closed.)

Specifications

  1. Model: MCCGQ11LM
  2. Dimensions: 41 × 22 × 11 mm (1.61 × 0.87 × 0.43 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR1632
  5. Maximum Detection Distance: 22mm
  6. Operating Temperature: -10° ~+50° C
  7. Operating Humidity: 0~95% RH, no condensation
Motion Sensor

Product introduction

Aqara motion sensor detects human motion using infrared rays. By linking with Gravio, you can use it in various scenarios, such as turning the light on/off automatically when activity or human presence is detected.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-Occupancy" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the Gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button in Gravio Studio.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick it to the desired position.

Option 3 : Stick the Motion Sensor to the stand, and stick the stand to where you need it.

Notes: Keep the surface clean and dry.

The recommended installation height is 1.2 to 2.1 meter. If the installation height is below 1.2 meter, the detection area will be decreased; if above 2.1meter, the detection area might have blind spots.

Note that the lens should be aligned with the detection area when installing, and place or pasted as close as possible to the edge of a table or cabinet.

Specifications

  1. Model: RTCGQ11LM
  2. Dimensions: 30× 30 × 33 mm (1.18 × 1.18 × 1.30 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2450
  5. Maximum Detection Distance: 7meter
  6. MaximumDetection Angle: 170°
  7. Operating Temperature: -10°~ +45° C
  8. Operating Humidity: 0~95%RH, no condensation
Temperature Sensor

Product introduction

The Aqara temperature and humidity sensor sends indoor temperature, humidity, atmospheric pressure in real time to Gravio.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-Temperature" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick it to the desired position.

Note: Keep the surface clean and dry.

Specifications

  1. Model: WSDCGQ11LM
  2. Dimensions: 36 × 36 × 9 mm (1.42 × 1.42 × 0.35 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2032
  5. Temperature Range and Precision: -20°~ +50° C, ± 0.3° C
  6. Humidity Range and Precision: 0~100% RH, ± 3%
  7. Atmospheric Pressure Range and Precision: 30 kPa ~ 110 kPa, ± 0.12 kPa
  8. Operating Humidity: 0~95% RH, no condensation
Wireless Mini Switch

Product introduction

The Aqara wireless switch is a compact design and low power consumption remote control switch. You can assign Gravio action to each operation such as press once, press twice, or press and hold.

Note: This product is for indoor use only.

Quick Setup

  1. Insert the Gravio receiver in the USB port of your PC or Mac, then start the Gravio Edge Server.
  2. Remove the sensor's battery insulation seal.
  3. Start Gravio Studio on your PC, iPhone or iPad, tap to select Gravio Server which you just started, and create areas to describe where the Sensors are and layers to group them by function. Please select "Aqara-WirelessSwitch" from the layer selection list.
  4. Connect the Graivo receiver to this layer.
  5. From the Gravio Studio device list, tap the gravio Receiver line.
  6. If this sensor is the first to be connected sensor, press "Reset". (Please do not reset your receiver before adding subsequent sensors.)
  7. Next, press the "Pairing" button.
  8. When pairing is in progress, you will see a count-down. During that count-down, press the button on the sensor once.
  9. When the sensor connected to Gravio Studio screen is displayed, connection is completed.

Note: If the connection fails, please move the accessory closer to the Gravio Receiver and try again.

Installation

Option 1: Place it directly in the desired position.

Option 2 : Remove the protective film, and stick the wireless button to the desired position.

* Keep the surface clean and dry.

Specifications

  1. Model: WXKG11LM
  2. Dimensions: 45 × 45 × 2 mm (1.77 × 1.77 × 0.47 in. )
  3. Wireless Protocol: Zigbee
  4. Battery: CR2032
  5. Operating Temperature: -10° ~ +50° C
  6. Operating Humidity: 0~95% RH, no condensation